Welcome to AIMEDD Gifts Mall

ICS-CTRL, PI-REPEATER-2X-MT3 {1}
ICS-CTRL, PI-REPEATER-2X-MT3 {1}

ICS-CTRL, PI-REPEATER-2X-MT3

$99 $334.95

ICS-CTRL, PI-REPEATER-2X-MT3

Availability:
In Stock
  • Estimated Delivery:Jul 10 - Jul 17

  • Free Shipping & Returns: Free Shipping for all orders. Free Return

Guarantee safe & secure checkout

ICS-CTRL, PI-REPEATER-2X-MT3
ICS-CTRL, PI-REPEATER-2X-MT3
The PI-REPEATER-2X-MT3 system is everything you need to add a PI-REPEATER-2X controller to your Daniels/Codan radio setup. This system is designed specifically for the MT3 backplane interface, but may work with others that have a common pinout. The PI-REPEATER-2X-MT3 comes fully assembled. Included is a PI-REPEATER-2X interface board, Raspberry Pi 3B, 32GB microSD card
preloaded), 12V->5V2A power supply (hardwired to the pi), and all the cables and hardware to bring it together.
We recommend the PI-REPEATER-2X-MT3 for chassis that are configured with either 2 sets of Tx/Rx, or a chassis with 1 TX/RX and amp that will also have a control radio.
If using a chassis configuration with a single TX/RX, and no control radio, you might also consider the PI-REPEATER-1X-MT3 .
The PI-REPEATER-2X controller board includes a number of extra features that help with integration, and expansion to other equipment and make the installation easier.
Built in audio
an on-board SGTL5000 audio codec eliminates the need for external USB audio dongles to be able to get input audio
audio adjustments
Level adjustments – 18 turn potentiometers allows for fine adjustments to both input and output audio channels
Flat audio – Flat audio can be enabled with a simple slide switch, this is available independently for both in
put audio channels
GPIO Expander – [email protected] 3.3V GPIO in a DSUB-15 connector interface, great for a variety of NO/NC type sensors, LEDs, control signals, etc.
Analog to Digital Converter – 8 Analog inputs (5V reference) through a DSUB-9 connector interface, great for environmental sensors.
GPS
A socket is provided for adding a Spark-Fun designed GPS receiver, this provides a convenient reliable method for having accurate time synchronization between sites, and for network time if needed. The GPS receiver board uses a SMA connector to allow for a variety of antenna options.
Radio Signal interfacing
COS (COR) and CTCSS inputs are to tolerant of 12V type radio control signals that can be either active high or active low type. The active high and active low is selectable with a simple slide switch
PTT interfaces provides an active low signal to the radio that is capable of handling up to 2A of current, plenty to handle several modern radios and relays.
I2C expansion header (not preinstalled) – Gives easy access to the I2C bus for adding additional I2C based devices
SPI expansion header (not preinstalled)- SPI (CS1) is available for adding a SPI based device
UART Header – The simple (TX/RX) UART interface is shared with the GPS socket, but a slide switch will allow you to quickly select between the 2 options. Key Specifications
Number of full duplex channels: 2
Power Consumption [email protected]
Operating System: Raspbian Stretch (Linux)
Repeater Controller Software – SVXlink (open source)   Shipping
Shipping cost: US - $6 USD
International - $20 USD
Delivery time: US - 3-5 days typical
International - 1-3 weeks typical depending on location and customs
Payment
We accept the following payment methods:
Paypal
1 review for Chaz Kangeroo Hoodies

Aliquam fringilla euismod risus ac bibendum. Sed sit amet sem varius ante feugiat lacinia. Nunc ipsum nulla, vulputate ut venenatis vitae, malesuada ut mi. Quisque iaculis, dui congue placerat pretium, augue erat accumsan lacus

Note: HTML is not translated!
    Bad           Good
  • Total $0.00